攪拌機以其集加料與攪拌于一體，節省人力物力而得到廣泛應用。攪拌機有物料時，不能停止攪拌，防止物料凝固。許多用戶在使用自供式混凝土攪拌機時，都遇到了攪拌軸停止轉動的現象。出現這種情況的原因是什么？

Mixer is widely used because it integrates feeding and mixing, and saves manpower and material resources. When there is material in the mixer, the mixing cannot be stopped to prevent the material from solidifying. Many users encounter the phenomenon that the mixing shaft stops rotating when using the self supplied concrete mixer. What is the reason for this?

在生產過程中，當混凝土自進式攪拌機攪拌軸停止轉動或轉動稍慢時，為異常現象。如果發生這種情況停止機器，檢查是否有以下三種情況。

In the production process, when the mixing shaft of the concrete self feeding mixer stops rotating or rotates slightly slowly, it is an abnormal phenomenon. If this happens, stop the machine and check whether the following three conditions exist.

電機傳動皮帶是否松動？自拌混凝土攪拌機電機傳動皮帶過松也會導致商品混凝土攪拌機攪拌軸轉動緩慢或停止轉動。電機傳動皮帶過松導致動力傳遞不足。

Is the motor drive belt loose? Loose drive belt of self mixing concrete mixer motor will also cause slow rotation or stop rotation of mixing shaft of commercial concrete mixer. The motor drive belt is too loose, resulting in insufficient power transmission.

是否嚴重超載？攪拌機攪拌軸超過正常工作負荷時，會使攪拌軸緩慢轉動。如果負載過大，會導致攪拌軸停止或彎曲。

Is it seriously overloaded? When the mixing shaft of the self mixing concrete mixer exceeds the normal working load, the mixing shaft will rotate slowly. If the load is too large, it will cause the mixing shaft to stop or bend.

攪拌葉片或側葉片與筒體內壁之間是否有大的異物？在這種情況下，自動混凝土攪拌機的攪拌軸將停止轉動或轉動緩慢。攪拌葉片或側葉片與罐內壁之間有較大異物，也會導致攪拌軸停止運轉。異物卡住的原因是攪拌葉片或側葉片與罐內壁間隙過大，尤其是石塊。

Is there any large foreign matter between the mixing blade or side blade and the inner wall of the cylinder? In this case, the mixing shaft of the automatic concrete mixer will stop rotating or rotate slowly. There are large foreign matters between the mixing blade or side blade and the inner wall of the tank, which will also cause the mixing shaft to stop running. The reason why the foreign matters are stuck is that the gap between the mixing blade or side blade and the inner wall of the tank is too large, especially the stones.

以上便是問題的相關解答內容了，如果您想獲取更多相關信息，就來關注我們網站http://ffyhk.cn吧！

The above is the relevant answers to the questions. If you want to get more relevant information, please follow our website http://ffyhk.cn Come on!